Naslov (eng)

Integrated process planning die-design and simulation in sheet metal rubber forming : doctoral dissertation

Autor

Benisa, Muamar M.

Doprinosi

Babić, Bojan R., 1959-
Stefanović, Zoran, 1948-
Sedmak, Aleksandar, 1955-
Grbović, Aleksandar, 1970-
Rakin, Marko, 1966-

Opis (eng)

При производњи делова од лима без дефеката користи се приступ покушаја и грешака, који значајно зависи од искуства и вештине оператора. У фази пројектовања искуство пројектанта и пројектанта технолошког процеса би требало да допринесе смањењу броја покушаја потребних за минимизацију времена одзива и трошкова уз максимизацију производности и квалитета. Обрада у алатима са језгром од гуме значајно унапређује обрадљивост дела од лима зато што су контактне површине између крутог дела калупа и гуменог језгра флексибилне. Овај метод омогућује израду комплексних делова од лима уз ниске трошкове јер је потребан смо један део калупа од чврстог материјала. У области аерокосмонаутике делови се производе у малим серијама. То значи да није исплативо да се не исплате веће инвестиције за алате у производњи делова од лима. Из тог разлога препоручује да се током концептуалног пројектовања примењује метода коначних елемената за симулацију технолошког процеса. На тај начин се могу добити значајни одговори у вези анализе процеса и могу се предвидети дефекти који могу настати током обраде. На тај начин се могу направити потребне модификације пре израде алата и израде делова. Ова теза се бави симулацијом израде делова од легура алуминијума и истраживањем фактора обраде као што су деформациона сила, напони и деформације повезане са процесом обраде у алату са гуменим језгром, као и могућностима овог процеса за израду делова који представљају ребра репа авиона...

Opis (eng)

To produce a new component there is a trial and error stage to obtain a sheet metal part without defects, which strongly depends on an operator’s skill and experience. At the design stage, the experience of the designer and manufacturers should give an important aid to reduce trials to enable the minimization of response time and cost with the maximization of the product quality. Rubber pad forming highly improves the formability of the blank because the contact surfaces between the rigid die and the rubber pad are flexible. This method enables production of sheet metal components with the complex contour at relatively low cost because only one rigid die is required. However, in the aerospace field, parts are produced in small sheet metal bending and small number of components. It means that large investments are cost-effective for the production of structures formed by the sheet metal press. For these reasons it is recommendable to use finite element (FE) simulation of the manufacturing process during the conceptual design [1]. Moreover, it could give important answers in the analyses of the processes and could predict the defects that may occur. Therefore, the modifications can be easily done before the tool manufacturing and part production. This thesis is concerned with a forming simulation of aluminum alloy parts and investigation of significant parameters (such as forming force and stress, and strain distribution in a blank) associated with the rubber-pad forming process and the capabilities of this process regarding the manufacturing of the aircraft tail ribs. These finite element models of rubber pad forming process are studied in this dissertation to investigate the effect of tool geometry for supporting ribs with the lightening hole of the aircraft tail. The different tool geometries for supporting ribs with the lightening hole are iii used to optimize the tool geometry and to find out the right design of the tool for a defect free product. The simulation and investigation carried out identifies the stress and strain distributions in a blank as well as the forming force. This research shows a good correlation between FE simulations and experimental results...

Opis (eng)

Mechanical Engineering-Production Engineering / Машинство-Производно машинство Date of defence: 7. 11. 2013.

Jezik

engleski

Datum

2013

Licenca

© All rights reserved

Predmet

OSNO - Opšta sistematizacija naučnih oblasti, Plastična obrada

Обрада лима у алатима са гуменим језгром, Симулација методом коначних елемената, Оптимизација, Еластично враћање

OSNO - Opšta sistematizacija naučnih oblasti, Plastična obrada

Rubber pad forming, sheet metal forming, FE M simulation, Optimization, springback, wrinkling